Wszystkie kontrole, które wykonujemy

Zanim projekt trafi do Ciebie, przechodzi przez kontrole wymienione poniżej. Część z nich zatrzymuje projekt całkowicie, inne zgłaszają uwagę i zostawiają decyzję Tobie. Ta strona wymienia je wszystkie — łącznie z tymi, które tylko doradzają, i z tą jedną, która celowo milczy.

Ta lista jest generowana z kodu, który wykonuje kontrole — nie jest pisana ręcznie. Jeśli kontrola zostanie przemianowana, usunięta albo jej waga obniżona, ta strona zmieni się razem z nią, a nasz build nie przejdzie, jeśli obie wersje kiedykolwiek się rozjadą.

Blokuje projekt
Fails closed. A design that breaks this rule is sent back to be fixed before you ever see it.
Chroniona testami
Advisory in production, but fail-closed in our regression suite — so it cannot get worse without a build going red.
Doradcza
Runs on every design and is reported, but does not block. Usually a workshop decision rather than a safety or fit problem.
Zgłasza tylko to, co potrafi udowodnić
Implemented, but reports only the cases it can decide with evidence. It stays quiet rather than guess.

Spójność projektu

Is this really the piece of furniture it claims to be?

  • Nothing scrapes the floor

    Blokuje projekt

    Fronts and carcass keep a real clearance above the floor, so a door does not bind on carpet.

    Podstawa: Internal policy: 10 mm minimumC1

  • One carcass, one front style

    Blokuje projekt

    A single cabinet does not mix door styles by accident.

    Podstawa: Internal design ruleC2

  • One opening, one front

    Blokuje projekt

    Two fronts over the same opening means one of them cannot open.

    Podstawa: Internal design ruleC3

  • Hinges are spread along the door

    Blokuje projekt

    Hinges bunched near the middle leave the door corners unsupported.

    Podstawa: Blum mounting guidanceC4

  • Shelving has adjustable shelves

    Blokuje projekt

    A shelving piece where every shelf is fixed is not shelving.

    Podstawa: Internal design ruleC8

  • Every part can be transported

    Blokuje projekt

    No panel is too large to get into the room it is destined for.

    Podstawa: Internal policy: 1800 mm maximum edgeC9

  • The back matches how it is built

    Blokuje projekt

    A back declared as grooved is grooved; a structural back is thick enough to be structural.

    Podstawa: InternalC10

  • Handleless openings fit a hand

    Blokuje projekt

    A push-to-open gap you cannot get a finger into is not an opening.

    Podstawa: Internal policy: 35 mm minimumC11

  • Wall-mounted units sit against the wall

    Blokuje projekt

    A wall fixing that stands the unit off its wall makes the load worse, not better.

    Podstawa: Internal policy: 20 mm maximum standoffC12

  • The reveal between fronts is a gap, not a slot

    Blokuje projekt

    Too wide and the gap reads as a mistake; too narrow and the doors catch.

    Podstawa: Blum: 1.5 mm minimum, 3 mm typicalC14

  • A front can open through its own design

    Blokuje projekt

    Every door, flap, drawer and sliding leaf, with what is fixed to it, is swept through its own motion against the whole design, carcass included. Only a motion known from the maker's linkage or measured off its CAD can fail a design.

    Podstawa: Maker linkage paths (Blum, GTV, Hettich), swept geometryC15

  • Nothing is cut away for hardware that is not there

    Blokuje projekt

    A back panel is notched at the top so the wall brackets can reach the wall. Every notch is checked against the bracket it was cut for, so a panel nowhere near one is not left with a hole through to the wall behind it.

    Podstawa: Internal design ruleC25

  • A grooved back sits in a groove

    Blokuje projekt

    A back can be captured two ways, and they are not interchangeable: a rabbet is a step along the rear edge, a groove is a closed channel with material behind it, which is what hides the panel's edge on a piece you can walk around. A back asked to be grooved is checked to have that material behind it.

    Podstawa: AWS casework backs (½" shoulder)C26

  • A hinge stands clear of the shelves

    Blokuje projekt

    A shelf behind a door must not sit where the door's hinges are. On a short door the hinges cannot move far enough to clear it, so the door has to end where the shelf is — the door split and the shelf must agree.

    Podstawa: Internal design ruleC29

  • The piece has the geometry its type implies

    Chroniona testami

    A bed frame has what makes it a bed frame. This class is still open — some archetypes are not yet described well enough to judge.

    Podstawa: Internal archetype definitionsC6

  • The interior you asked for is there

    Chroniona testami

    Requested shelves, drawers or hanging rails actually appear in the design.

    Podstawa: Internal: prompt versus resultC7

  • No two parts occupy the same space

    Chroniona testami

    Every part is checked against every other — including the drawer boxes and runner hardware, which are built after the design is solved and were previously unchecked. Parts that are fastened together, or belong to the same drawer, are meant to interlock and are not counted.

    Podstawa: Internal: solid-body clearanceC16

  • A drawer box fits behind its own front

    Chroniona testami

    The box stays under the top of the opening it slides into, so it cannot foul the shelf above it or stand proud of the front it is screwed to.

    Podstawa: Internal design ruleC17

  • Fittings sit inside the cabinet they belong to

    Chroniona testami

    Hinges, plates, runners and cam fittings are checked against the cabinet they are fitted to, so a hinge cannot be drawn hanging outside the door it opens.

    Podstawa: Internal: fitting placementC18

  • Every front covers the opening it was made for

    Chroniona testami

    A door is checked against the compartment it was drawn to close, so one cannot end up covering half an opening and leaving the rest of the cabinet exposed.

    Podstawa: Internal design ruleC19

  • Decoration is only built where it can be seen

    Chroniona testami

    The vertical battens of a slat wall are not fitted behind a cabinet that hides one completely — that is material and a cut part nobody will ever see.

    Podstawa: Internal design ruleC20

  • Every front has a way to open it

    Chroniona testami

    A door or drawer front carries a handle, a finger pull, a lipped edge or a press-to-open mechanism. Asking for no handle without choosing one of the others leaves a front nobody can open.

    Podstawa: Internal design ruleC21

  • Tall storage is anchored to the wall

    Chroniona testami

    A wardrobe, chest or bookcase tall enough to tip is supplied with a wall anchor. It still stands on the floor — the anchor only stops it falling forward.

    Podstawa: ASTM F2057 / EN 14749 tip-overC22

  • Every drawer can be pulled out

    Chroniona testami

    A drawer is opened against everything around it, including the hardware inside the cabinet — a box driven into the arm of the hinge beside it stops halfway and no drawing shows it.

    Podstawa: Internal design ruleC23

  • A desk leaves room for your legs

    Chroniona testami

    The knee bay of a desk is measured from the floor to whatever hangs over it. A drawer band or a shelf that brings the ceiling below 650 mm makes a desk nobody can sit at, however right it looks in a drawing.

    Podstawa: BS EN 527-1 legroomC24

  • Nothing stands under a drawer runner

    Chroniona testami

    A runner is screwed to the side panel just above the panel under it, and a connector set into that panel can stand proud of its face. The real shapes of both are measured, and the runner must clear anything under it by 0.3 mm.

    Podstawa: Internal design ruleC27

  • A hinge touches only its door and its side

    Chroniona testami

    A hinge's cup is bored into the door and its mounting plate is screwed to one side or divider. Measured on the hinge's real shape, no part of it may reach into any other panel — a top or bottom, a hanger, a drawer unit — that happens to sit where the hinge does.

    Podstawa: Internal design ruleC28

  • A drawer runs clear of the panel beneath it

    Chroniona testami

    A drawer box must not rest on the panel it slides over. Touching it, the box drags along the cabinet bottom every time it opens and wears both.

    Podstawa: Internal design ruleC30

Wykonalność i konstrukcja

Can this be made, and will it hold together?

  • The build order can be carried out in order

    Blokuje projekt

    Every step is checked with only the panels placed before it in the way, not against the finished piece — so a fastener the order reaches after something has closed over it is caught, and so is a panel scheduled after the grooves holding it have shut.

    Podstawa: Our own build sheet, walked step by stepassembly_order_feasible

  • The parts list matches the holes

    Blokuje projekt

    Every fitting in the bill of materials has its holes in the drilling plan, and vice versa.

    Podstawa: Internal cross-checkbom_matches_drill_plan

  • Every connector you asked for landed on a joint

    Blokuje projekt

    If you asked for a particular connector on a particular part, this confirms it reached a real joint and was buildable there. An instruction that quietly matched nothing would leave the piece built the standard way with no one told.

    Podstawa: Internalconnector_overrides_honoured

  • Doors stay within the flatness warranty

    Blokuje projekt

    Doors above 610 × 2134 mm fall outside the size for which flatness is warranted; past that we specify a straightener.

    Podstawa: AWS (Architectural Woodwork Standards)door_within_max_size

  • Drawer fronts are actually attached

    Blokuje projekt

    Each front has the fixings that hold it to its box.

    Podstawa: Internal completeness checkdrawer_fronts_fastened

  • Runner holes are measured from a stated edge

    Blokuje projekt

    Every runner fixing names the edge it is measured from, so the shop cannot read it from the wrong side.

    Podstawa: Internal: bores carry their own datumdrawer_rail_datum

  • Every drawer has both its runners

    Blokuje projekt

    A drawer with one rail specified is a drawer that will not open.

    Podstawa: Internal completeness checkdrawer_rails_complete

  • The runner fits the cabinet depth

    Blokuje projekt

    Nominal length is not longer than the carcass that has to hold it.

    Podstawa: Blum nominal-length tabledrawer_slide_fits_depth

  • The runner fits the opening

    Blokuje projekt

    The chosen runner physically fits the cabinet it is specified for.

    Podstawa: Runner specificationsdrawer_slide_in_opening

  • Every panel joint has a connector

    Blokuje projekt

    A panel butt joint takes a cam, or a confirmat driven through the face panel from outside where no cam can be turned. Dry dowels alone are not a fastening, and a joint that can take neither is refused rather than shipped.

    Podstawa: Our own knock-down policy; EN 16122every_joint_has_a_connector

  • Nothing is left off the instructions

    Blokuje projekt

    Every part on the cut list is named by a step that tells you where it goes. A part with no instruction is one you would find left over in the box.

    Podstawa: Internalevery_part_has_a_step

  • Hardware does not collide with hardware

    Blokuje projekt

    Hinges, runners and connectors have room for each other and for the panels they mount to.

    Podstawa: Manufacturer clearance datahardware_panel_clearance

  • Every panel joint is held at two points

    Blokuje projekt

    A joint fixed by one connector is a pivot: the panel turns about it, and spins with the screw as it is tightened. Every panel joint has two connectors, or a connector and a wooden dowel; an end too short for two is left unfastened only where the part is held at two points along its length.

    Podstawa: Internal: the connection graph in joinery.pyjoints_hold_at_two_points

  • Every module of an assembly is re-checked in place

    Blokuje projekt

    A multi-part piece is validated as built, not only per module.

    Podstawa: Internalmodule_revalidation

  • Nothing is bored into an edge the machine cannot reach

    Blokuje projekt

    A shop whose CNC bores only the broad faces gets a design it can cut whole. A bore into a panel's edge would be left out of its program, so a design that needs one is refused, and so is one that leaves such a bore to the bench.

    Podstawa: Internalno_edge_bores_on_a_face_only_machine

  • Nothing is floating

    Blokuje projekt

    Every part is connected to the piece by a real joint. A panel with no fixings is a drawing, not furniture.

    Podstawa: Internal: the connection graph in joinery.pyparts_all_fastened

  • Every part fits on a sheet

    Blokuje projekt

    No part is larger than the biggest board it could be cut from.

    Podstawa: Stock sheet sizesparts_fit_sheet

  • A bought drawer box has a side height that fits

    Blokuje projekt

    Each drawer on a box system takes the tallest side height the maker sells at its length whose space requirement the opening meets.

    Podstawa: Blum catalogue 2024/25, space requirement and cutting per side heightpurchased_box_side_fits

  • Shelves carry their load without sagging

    Blokuje projekt

    Deflection stays within span/200 for the load the shelf is designed for. Beyond that a shelf looks bowed even though it has not failed.

    Podstawa: EN 16122 §6.1.4shelf_load_capacity

  • A sliding front hangs on a set that carries it

    Blokuje projekt

    Every sliding leaf is within the size, height and weight limits of the set it is bored and billed for. Where no set we build with can carry the leaves, the design is refused rather than built with doors nothing holds.

    Podstawa: Manufacturer sliding-system limits (Hettich)sliding_system_serves

  • Every thickness is a board you can buy

    Blokuje projekt

    Each part's thickness matches real stock. A 17 mm panel is not a board, it is a rounding error.

    Podstawa: Our board catalogue (MFC 8/16/18/25 mm)thickness_in_catalog

  • Reach ranges are checked

    Doradcza

    Where accessible reach applies, storage sits within it.

    Podstawa: ADA reach rangesada_reach_range

  • Cam joints are wide enough for the bolt to cross them

    Doradcza

    A Minifix bolt reaches 24 or 34 mm and nothing between. A panel narrower than that across the joint is dowelled instead.

    Podstawa: Häfele Minifix / Hettich Rastex bolt lengthscam_joints_reachable

  • Cams are not fitted to boards too thin for them

    Doradcza

    A Ø15 cam needs roughly 12 mm of board; thinner and it breaks out of the face.

    Podstawa: Hettich Rastex specificationcam_min_panel_thickness

  • Connectors are not crowded together

    Doradcza

    Adjacent fittings keep enough material between them to hold.

    Podstawa: Manufacturer minimum spacingsconnector_min_spacing

  • Joints held by dowels alone are named as such

    Doradcza

    Where no cam can be turned — a closed plinth void, a rail's end grain — the joint is dry wooden dowels. Those resist racking and not pull-out, and the build has to say so rather than imply a knock-down connector is there.

    Podstawa: EN 16122 / trade practice; our own knock-down policydowel_only_joints_are_shear_keys

  • The drawer box fits its runners

    Doradcza

    Box width equals the opening minus what the runner takes on each side — the single most common build error.

    Podstawa: Blum / Rockler runner specificationsdrawer_box_fits_slides

  • Drawers are a sensible shape

    Doradcza

    Very tall or very shallow drawers rack and jam; the proportion is checked against normal practice.

    Podstawa: AWS / trade practicedrawer_proportion

  • You can see into the top drawer

    Doradcza

    A drawer above roughly 1400 mm is one whose contents you cannot see, only feel for.

    Podstawa: Ergonomic guidancedrawer_reach_height

  • Runners are rated for what the drawer will hold

    Doradcza

    Load class against the drawer's size and expected contents.

    Podstawa: Blum / Hettich load classesdrawer_slide_load_ok

  • Hinges can carry their door

    Doradcza

    Door weight against the hinge count and rating.

    Podstawa: Blum load tableshinge_load_within_rating

  • Oversized board is flagged, not hidden

    Doradcza

    A part that only fits a special-order long board is allowed, but you are told before you order.

    Podstawa: Stock sheet sizesoversized_board_required

  • Shelves line up across the piece

    Doradcza

    Shelves at the same nominal height actually sit at the same height in neighbouring bays.

    Podstawa: Internal quality ruleshelf_line_alignment

  • Shelf supports are rated for the load

    Doradcza

    The studs, not just the board, can carry it — a strong shelf on weak supports still falls down.

    Podstawa: Manufacturer load ratings (Häfele, Hettich)shelf_supports_rated_for_load

  • Long runs are flagged for a seam

    Doradcza

    A run longer than any stock length needs a joined or mitred seam, and you are told so rather than finding out on site.

    Podstawa: Stock lengthsspanning_length_stock

  • Worktops and plinths use stock thicknesses

    Doradcza

    Linear stock is checked against what is actually sold.

    Podstawa: Our board cataloguespanning_thickness_stock

  • Tall cases are braced

    Doradcza

    A tall carcass gets a fixed mid shelf, which is what stops the sides bowing.

    Podstawa: Internal structural ruletall_case_mid_shelf

  • A cabinet hung on L-brackets says what each must carry

    Doradcza

    A generic steel L-bracket carries no rating we can stand behind, so instead of passing it the design states the load per bracket, and the bracket bought must be labelled for at least that.

    Podstawa: Internalwall_bracket_load_stated

Obróbka i otwory

Are the holes and cuts correct and machinable?

  • Captured backs match the cut made for them

    Blokuje projekt

    Every captured back edge agrees with its cut allowance and the carrier that was actually routed for it.

    Podstawa: Internal geometric checkback_capture_closure

  • Holes do not run into each other

    Blokuje projekt

    Two bores that intersect leave no material between them and the fixing pulls out.

    Podstawa: Internal geometric checkbore_collision

  • Every connector's holes are in the drill plan

    Blokuje projekt

    The fitting and the holes that receive it never disagree.

    Podstawa: Internalconnector_bore_closure

  • Every joint is modelled, so the checks above have something to read

    Blokuje projekt

    The two checks above read the connector model. A joint missing from it would leave them with nothing to look at and nothing to report, which reads the same as a clean result. This confirms every joint in the piece actually reached them.

    Podstawa: Internalconnector_model_covers_joints

  • Every connector sits on both its panels

    Blokuje projekt

    A joint needs two sides; a connector with only one is not a joint.

    Podstawa: Internalconnector_panel_closure

  • Every door has its hinges, cupped and plated

    Blokuje projekt

    For each door, the cup is bored in the door and the matching plate holes are in the panel it hangs on — both halves, or the door does not hang.

    Podstawa: Internal: the drilling plan against the computed hinge countdoor_hinge_closure

  • Every door's hinge can set its overlay

    Blokuje projekt

    How far a door covers the panel it hangs on is set by the hinge's crank and its mounting plate. A door on a gable takes an overlay hinge, one sharing a divider with its neighbour the half-overlay hinge; a door no hinge reaches cannot hang where it is drawn.

    Podstawa: Blum catalogue 2027/2028 p.71, Drilling distance TB tablesdoor_overlay_reach

  • Legs, panels and supports get the hardware they need

    Blokuje projekt

    Each element type has the fixings its role requires, rather than only the ones someone remembered.

    Podstawa: Internal completeness checkelement_hardware_expectations

  • Every fitting has a panel at both of its ends

    Blokuje projekt

    A drawer runner is a pair, one rail each side, and a shelf pin needs something to sit in. A fitting with one end in mid-air is hardware screwed to nothing.

    Podstawa: Internal: fitting anchoragefitting_end_closure

  • Every flap has its lift mechanism and no stray hinge

    Blokuje projekt

    A drop-down or lift-up front is held by a mechanism on both gables of its bay, not by hinges — so we check the two arms are there and that nothing bored cup hinges into it by mistake.

    Podstawa: Internal: the fabrication model against the flaps in the layoutflap_lift_closure

  • No hole breaks out the far side

    Blokuje projekt

    Depth stays within the panel unless the hole is meant to go through.

    Podstawa: Internal geometric checkhole_bore_within_material

  • Every hole starts on a real surface

    Blokuje projekt

    A bore whose mouth is not on the face of a part is a bore the machine cannot make.

    Podstawa: Internal geometric checkhole_mouth_on_surface

  • Every hole says what it is for

    Blokuje projekt

    No unexplained holes: each one names the fitting it serves.

    Podstawa: Internalhole_purpose_claimed

  • A sloping top is there and lands on both gables

    Blokuje projekt

    On a piece cut to a diagonal, the angled top board must exist, actually be tilted, and reach far enough at both ends to sit on the sides rather than on air.

    Podstawa: Internal: the solved geometry against the slope that was asked forraked_top_closure

  • Every drawer box is the size its runner dictates

    Blokuje projekt

    The runner article decides the box — its width, its length and the clearance each side. A box sized to the opening instead of to the runner does not slide.

    Podstawa: Manufacturer runner specifications (Blum)runner_box_fit

  • Sliding fronts are contained and can sweep

    Blokuje projekt

    Tracks are fastened, every leaf is held by a track pair, and the volume the leaf sweeps through is clear.

    Podstawa: Internal geometric checksliding_track_closure

  • How much of the drilling a manufacturer record covers is stated plainly

    Doradcza

    We publish the proportion of bores backed by a manufacturer record and name the families that are not — including that a first article is required before any production batch. This check always reports; it exists to disclose coverage, not to pass.

    Podstawa: The manufacturer drilling records in our fittings configrecorded_boring_coverage

  • Bores match the manufacturer's published spec

    Doradcza

    Where a fitting has a drilling record, every hole we plan for it is compared against that record and any contradiction is reported.

    Podstawa: Manufacturer CAM data (Blum, Häfele, Hettich)recorded_boring_in_spec

Kontrola, która blokuje projekt, nie oznacza, że projekt zostaje odrzucony — wraca do poprawy i trafia do Ciebie naprawiony. Uwagi doradcze pokazujemy obok projektu, żeby decyzja pozostała Twoja.